For AI assistants: this page as plain markdown is at https://docs.voicelogica.ai/raw/phone-systems/unify-siemens.md, and https://docs.voicelogica.ai/llms.txt lists the docs by topic, one file each, small enough to read whole. Read those rather than this HTML page.
Unify / Siemens
Ce contenu n’est pas encore disponible dans votre langue.
How Voice Logica connects
Section titled “How Voice Logica connects”OpenScape Business registers to Voice Logica as an Internet Telephony Service Provider (ITSP) (way 1). Voice Logica creates the trunk and gives you a server, a username and a password; in OpenScape it is one more provider next to your carrier.
- Calls the PBX routes to this provider are answered by the AI agent.
- The agent transfers callers back over the same provider with the extension’s number; with Use public number (DID) each station’s DID field rings that station.
Before you start
Section titled “Before you start”- S2M/T1/SIP trunks licences, one per simultaneous call to Voice Logica. A Warm transfer uses two until it connects.
- WBM in the Advanced profile (wizard) or Expert (codecs).
- At most 8 active ITSPs per system.
1. Create the connection in Voice Logica
Section titled “1. Create the connection in Voice Logica”Telephony - Trunks - Connect your PBX, pick Unify OpenScape Business and the agent. Keep the dialog open until it says Connected.
2. Add Voice Logica as a provider
Section titled “2. Add Voice Logica as a provider”- WBM → Setup → Wizards → Central Telephony → Internet Telephony → Edit. Untick No call via Internet, then Add.
- Base template. Provider Name
VoiceLogic(10 characters at most), tick Enable Provider. - Gateway Domain Name = the server.
- Provider Registrar: tick Use Registrar, host = the server, port 5060. Provider Proxy: the same host and port.
- OK & Next → Add account: Internet Telephony Station = the username, Authorization name = the username, Password = the password.
- Call number assignment = Use public number (DID), with a default number.
- Set Upstream (Kbps) high enough for the calls you expect; it caps simultaneous calls. Check that the provider shows as registered.
- Expert Mode → Telephony Server → Voice Gateway → Codec Parameters: G.711 A-law priority 1, frame size 20 ms, tick Transmission of DTMF Tones according to RFC2833.
3. Send calls to the agent
Section titled “3. Send calls to the agent”Use Expert mode → LCR (dial plan, routing table) to make a route, for example a code your staff dial, that uses the Voice Logica provider. To send a number, an attendant option or after-hours calls to the agent, forward that destination to an external number dialled over that route. Your Unify partner can confirm the best way for your release.
4. Let the agent transfer back to extensions
Section titled “4. Let the agent transfer back to extensions”With Use public number (DID), calls from Voice Logica reach the station whose DID matches the number the agent sends. In Voice Logica, add each person as a transfer destination: an External destination with that number, or a User with that extension. Use Warm transfer, so the agent comes back and takes a message when nobody answers.
5. Check it works
Section titled “5. Check it works”- The dialog says Connected; the provider shows as registered in WBM.
- Dial the route: the call appears in Calls.
Good to know
Section titled “Good to know”- Change Extended SIP Provider Data only with Unify support.
- HiPath 3000 (older): SIP providers arrived in later releases through the HG 1500 board. If yours cannot add a SIP provider, use an ISDN gateway or forwarding.
Frequently asked questions
Section titled “Frequently asked questions”How do I connect my Unify OpenScape Business to Voice Logica?
OpenScape Business registers to Voice Logica as an Internet Telephony Service Provider (ITSP), one more provider next to your carrier. In Voice Logica, open Telephony - Trunks - Connect your PBX and pick Unify OpenScape Business and the agent to get a server, a username and a password. In WBM, go to Setup → Wizards → Central Telephony → Internet Telephony, add a provider with the server as gateway domain, registrar and proxy (port 5060), add an account with the username and password, and set Call number assignment to Use public number (DID).
What licences does Unify OpenScape Business need for Voice Logica?
OpenScape Business needs S2M/T1/SIP trunks licences, one per simultaneous call to Voice Logica, and a Warm transfer uses two until it connects. The provider’s Upstream (Kbps) setting also caps simultaneous calls, so set it high enough for the calls you expect. A system can have at most 8 active ITSPs.
How do I send Unify OpenScape Business calls to the AI agent?
In Expert mode → LCR (dial plan, routing table), make a route that uses the Voice Logica provider, for example a code your staff dial. To send a number, an attendant option or after-hours calls to the agent, forward that destination to an external number dialled over that route. Your Unify partner can confirm the best way for your release.
Can the AI agent transfer callers back to Unify OpenScape Business extensions?
Yes. With Use public number (DID), calls from Voice Logica reach the station whose DID matches the number the agent sends. In Voice Logica, add each person as a transfer destination (an External destination with that number, or a User with that extension). Use Warm transfer, so the agent comes back and takes a message when nobody answers.
Can an older Siemens HiPath 3000 connect to Voice Logica?
Only if it can add a SIP provider: on the HiPath 3000, SIP providers arrived in later releases through the HG 1500 board. If yours cannot add a SIP provider, use an ISDN gateway or forward your number to Voice Logica.
